Home > Outboard Parts > Tools Testing Equipment for Outboards


Tools Testing Equipment for Outboards
Code / Price Name / Description
CDI511-73W   

$20.95 
   
Quantity in Basket: none
Wire Jumper Kit, Johnson, Evinrude


5-Wire Jumper Kit for Johnson/Evinrude
Replaces: 35-009

 
CDI511-7900   

$183.95 
   
Quantity in Basket: none
Switch Remote Starter Diagnositc Tool Mercury Outboard


511-7900 Mercury Remote Starter
Remote Starter works with most Mercury engines with the small cannon plug style head 1979-2006. 
Replaces boat side control harness at the engine to eliminate the boat harness as a source of trouble.

 
CDI511-9710   

$86.95 
   
Quantity in Basket: none
Tool Trigger Tester Mercury Chrysler Force Johnson Evinrude Outboard Motors


511-9710 Trigger Tester

Ideal for testing Mercury/Mariner triggers, Chrysler/Force triggers and Chrysler pre-amp and hall effect sensors, OMC 1988 and up V6 Quick Start timer bases. Also used on OMC OIS ignition, EFI.

 
CDI511-9764   

$20.95 
   
Quantity in Basket: none
Spark Gap Tester, Neon Indicator


511-9764 Neon Spark Tester 1 Cyl

Sealed spark tester can be used inline to the spark plug while the engine is running or it can be connected to engine ground for cranking speed tests.


Troubleshooting and Installation Guide (pdf)

 
CDI511-9766   

$62.95 
   
Quantity in Basket: none
Spark Gap Tester Tool Adjustable 1 to 8 Cylinder 511-9766


511-9766 Spark Tester
Spark tester can be used to test from 1 to 8 cylinders. Sealed design reduces the possibility of fire.
NOTE: If extension wires are needed, order P/N: 511-9903 (set of 4 wires).
Tech Sheet (pdf)

Troubleshooting and Installation Guide (pdf)

 
CDI511-9770   

$88.95 
   
Quantity in Basket: none
Wire Piercing Probe Set Outboard Testing Tool CDI511-9770


Piercing Probe Set
No need to disconnect harness or wires. Fully insulated probes have a spring loaded clamp with a tiny stainless steel pin that self centers and punctures the insulation. (Hole will normally reseal itself when the wire heats up.) Ideal for taking DVA readings on all engines and Jet Drive systems. This set is highly recommended for use with all meters and peak reading adapters. Set contains 1 Red and 1 Black probe.

 
CDI511-9772   

$64.95 
   
Quantity in Basket: none
Adapter DC Ampmeter Tool Outboard Motor DVA Testing CDI511-9772


511-9772 Ampmeter Adapter

Replaces: PL88
Use to replace ignition coil for testing DVA output from ignition pack if a bad coil is suspected.

 
CDI511-9773   

$75.95 
   
Quantity in Basket: none
Adapter Peak DVA Voltage Test Tool Fluke Meter for Outboard 511-9773


Peak Reading DVA Voltage Adapter for all Fluke digital volt meters. The readings will be close to the Stevens CD77 and Merc-Otronic specs. Ideal companion with Piercing Probe Set CDI511-9770. (See application chart in the Troubleshooting Guide for readings on OMC, Mercury, and Chrysler/Force.)

 
CDI511-9773NL   

$75.95 
   
Quantity in Basket: none
DVA Peak Voltage Adapter without leads


Peak Reading DVA Voltage Adapter for all Fluke digital volt meters. This adapter does not include the leads. If you require one with leads, please order CDI511-9773.
The readings will be close to the Stevens CD77 and Merc-Otronic specs. Ideal companion with Piercing Probe Set CDI511-9770. (See application chart in the Troubleshooting Guide for readings on OMC, Mercury, and Chrysler/Force.)

 
CDI511-9775   

$18.95 
   
Quantity in Basket: none
Load Resistor


Load Resistor To load the output of ignition modules when testing ignition coils. Used for testing DVA outputs from power packs and switch boxes. Replacement for Stevens PL88.

 
CDI511-9788B   

$68.95 
   
Quantity in Basket: none
Adapter Noise Filter Outboard Motor Testing 2 Cycle CDI 511-9788B


2 cycle noise filter used with Fluke 88 meter with RPM pickup, P/N 518-RMP80, to reduce outboard noise interference for inductive pickup applications.

 
CDI511-9800   

$9.95 
   
Quantity in Basket: none
Multimeter Resistor Test Card


Resistor Test Card for Multimeters  
CDI511-9902   

$24.95 
   
Quantity in Basket: none
Spark Tester Wire


7" Extension Wire for use with the CDI511-9766 Spark Gap Tester (Set of 4)

 
CDI511-9903   

$28.95 
   
Quantity in Basket: none
Spark Plug Tester Wire Leads


24" Extension Wire for use with the CDI511-9766 Spark Gap Tester (Set of 4)

 
CDI518-116   

$299.95 
   
Quantity in Basket: none
Multimeter Tool Fluke Meter Volt Meter Ohm Meter CDI 518-116


  • Replaces discontinued CDI518-16 (series) meters
  • AutoVolt: automatic AC/DC voltage selection
  • Large white LED backlight to work in poorly lit areas
  • Resistance and continuity
  • Min/Max/Average to record signal fluctuations
  • Can read micro amperage
  • Three-Year Factory limited warranty
  •  
    CDI518-88   

    $650.95 
       
    Quantity in Basket: none
    Fluke 88 Meter Kit with DVA Adapter


    Measures 2 and 4 stroke RPM ranges, volts, ohms, amperage, dwell, and injector pulse width. It has the capability of recording maximum and minimum RPM and volts. Backlight display readout is easy to-read in dim light. Offers specialized functions like RPM, duty cycle, dwell, relative change, lo-ohms and smoothing. Complete with deluxe test leads, probes and clips. Packaged in a battle-tough carrying case.

     
    CDI519-T125   

    $25.95 
       
    Quantity in Basket: none
    Thermomelt Temp Stiks, 125 degree F


    Stevens Thermomelt Temp Stiks, 125°F
    Long lasting Temp Stiks provide a quick and reliable means to check cooling systems. With engine warmed up, the temp stik is used like a crayon to make a mark on the head or block. The mark will appear dull and chalky. On a typical engine, the CDI-T125 (125°) should melt, turning liquid and glossy in appearance. If it does not, the engine is running too cold. A mark made with the CDI-T163 (163°) should not melt. If it does, the engine is running too hot.

     
    CDI519-T163   

    $25.95 
       
    Quantity in Basket: none
    Thermomelt Temp Stiks, 163 degree F


    Stevens Thermomelt Temp Stiks, 163°F
    Long lasting Temp Stiks provide a quick and reliable means to check cooling systems. With engine warmed up, the temp stik is used like a crayon to make a mark on the head or block. The mark will appear dull and chalky. On a typical engine, the CDI-T125 (125°) should melt, turning liquid and glossy in appearance. If it does not, the engine is running too cold. A mark made with the CDI-T163 (163°) should not melt. If it does, the engine is running too hot.

     
    CDI551-33-1   

    $159.95 
       
    Quantity in Basket: none
    Gearcase Filler


    Gearcase Filler With Check Valve
    A new design in gearcase fillers makes it easier to fill or flush gearcases. The check valve venting system helps prevent spilling any gear lube. The check valve on the vent allows you to remove the filler nozzle without loosing any appreciable amount of lubricant. Includes CDI551-33CV E-Z Fill. Replaces Stevens S33. Non-corrosive plastic container. Sturdy teardrop design resists tipping over.

     
    CDI551-334M   

    $11.95 
       
    Quantity in Basket: none
    Adaptor, Metric, Grease Filler


    Metric Adapter for Grease Filler
    Replaces 519-34M, 551-33M, 551-34M
    For all motors except Suzuki.

     
    CDI551-334S   

    $10.95 
       
    Quantity in Basket: none
    Gearcase Metric Adaptor for Suzuki


    Metric Adapter for Suzuki motors for use with CDI551-33GF E-Z Fill

     
    CDI551-33CV   

    $20.95 
       
    Quantity in Basket: none
    Filler Vent Check Valve


    Filler Vent Check Valve Calibrated check valve creates airlock to keep lube from running out while you install drain plug. Includes 4" Hose. A must for all shops! Included with CDI551-33GF.

     
    CDI551-34PV   

    $219.95 
       
    Quantity in Basket: none
    Pressure Vacuum Tester Tool Outboard and Outdrives CDI 551-34PV


    Pressure and Vacuum Tester Repairable metal unit does both vacuum and pressure testing.
    Screws into the fill on most applications and introduces your choice of vacuum or pressure to test units for leakage before installing on boat after repair or to check while still installed. Replaces S34 and V34 testers. Includes CDI551-34TN with hose.

     
    CDI551-34TN   

    $11.95 
       
    Quantity in Basket: none
    Threaded Nozzle, Pressure-Vacuum Tester


    Threaded Nozzle Fits and is included in CDI551-34PV Pressure/Vacuum Tester.

     
    CDI551-5110   

    $109.95 
       
    Quantity in Basket: none
    Tool Flywheel Holder Outboard for Mercury OMC Yamaha CDI 551-5110


    Flywheel Holder. New design has a high tensil strength, poly coated, woven belt for a more secure grip of flywheel. Longer handle provides a more comfortable grip for more leverage with less effort.
    Makes removing or installing the flywheel nut much easier.

     
    CDI551-9765   

    $39.95 
       
    Quantity in Basket: none
    Tool Marine Spark Plug Wire Puller Removal Tool CDI 511-9765


    Spark Plug Wire Puller With Unique Grounding Lead. Ground clip greatly reduces the chance of getting shocked.
    Used to pull each spark plug wire off while the engine is running to determine which cylinder is not firing. A Great diagnostic tool for all mechanics!

     
    CDI553-2697   

    $34.95 
       
    Quantity in Basket: none
    Tool Amphenol Insertion for Johnson Evinrude Outboard CDI 553-2697


    Amphenol Pin Insertion Tool. Installs the small pins on the plugs used by Johnson and Evinrude on Power Packs and Voltage Regulators.
    Replaces 322697

     
    CDI553-2698   

    $27.95 
       
    Quantity in Basket: none
    Pin Removal Tool


    Pin Removal Tool Replaces 322698

     
    CDI553-2699   

    $27.95 
       
    Quantity in Basket: none
    Socket Removal Tool


    Socket Removal Tool Replaces 322699

     
    CDI553-2700   

    $75.95 
       
    Quantity in Basket: none
    Tool Pin Amphenol Tool Set for Johnson Evinrude Outboard CDI 553-2700


    Amphenol Pin Tool Set Set contains one each of CDI553-2697 (insertion), CDI553-2698 (pin removal), and CDI553-2699 (socket removal) tools.

     
    CDI553-9702   

    $10.95 
       
    Quantity in Basket: none
    Sensor Gap Gage, Johnson, Evinrude


    Sensor Gap Tool, Use to reset the air-gap on Johnson/Evinrude sensor to flywheel clearance (Power Pack 3,4)

     
    CDI554-9706   

    $22.95 
       
    Quantity in Basket: none
    Amp Pin Removal Tool


    Amp Pin Removal Tool Used to remove the connector pins in the ignition system on Chrysler/Force engines using the Prestolite type ignitions. Also used on Mercury TPI sensor connectors.

     
    CDI911-9783   

    $12.95 
       
    Quantity in Basket: none
    Bullet Connector Kit


    Bullet Connector Kit Contains: 10 each Male Bullet with Boots, and 10 Female Bullets with Sleeves. Contains 10 pieces each of the male, female connectors and sleeves.

     
    CDI923-3356   

    $8.95 
       
    Quantity in Basket: none
    Kill Plug, Large


    Large Kill Plug Replaces 513356

     
    CDI923-3404   

    $11.95 
       
    Quantity in Basket: none
    Kill Plug, Small


    Small Kill Plug Replaces 123404

     
    CDI991-9705   

    $27.95 
       
    Quantity in Basket: none
    Grease Dielectric for Sealing Connections, Corrosion and Better Contact


    Dielectric Grease, 3 oz. tube. Used to help seal connections and inhibit corrosion. Gives better electrical contact and high voltage isulation. Dielectric Grease is used to keep water and corrosion out of connectors.

     
    MAL9-15400   

    $21.95 
       
    Quantity in Basket: none
    Ignition Safety Switch Lanyard for Universal Outboards Mercury 40970


    Lanyard Switch Ignition Safety
    Replaces: Mercury MP 40970
    Fits: Universal
    • Designed to kill ignition whe thrown fron controls.
     
    MAL9-79816   

    $6.95 
       
    Quantity in Basket: none
    Tester Ethanol Fuel Mercury 91-879172T28


    Tester for Ethanol percentage.
    Replaces: Mercury 91-879172T28

    Instructions: Fill with water to the line, fill with gas to the neck, put lid on and shake vigorously, stand vertical with cap on, let stand for 10 minutes, locate the gas/water separation line and read scale for percentage of Ethanol in the fuel.
     
    MAL9-81002   

    $15.95 
       
    Quantity in Basket: none
    Oil Pump, Lower Unit, Quart


    Oil Pump for Quart bottle, 4 cc pump and 3/8 - 16 swivel metal marine filler fitting. Ideal for adding Gear Lube and other fluids to small engines and marine lower units. Flexible Hose for hard-to-reach fill plugs. Adaptor included with pump fits Mercruiser, Mercury, OMC, Evinrude, Johnson, Volvo, Force, Sears, Gamefisher, and Honda (70 HP and up) Models

    Lower Unit Pump

    Lower Unit Pump


     
    SMI01117   

    $22.95 
       
    Quantity in Basket: none
    Oil - Fuel Filter Wrench


    This handy wrench removes screw on type marine water separator fuel filters and most oil filters
    Tough, forged stainless steel
     
    THDFMK-1-DP   

    $20.95 

       
    Quantity in Basket: none
    Double Flusher Twin Outboard Engine Flush Kit


    The Double Flusher™ twin outboard boat engine flush kit allows you to flush two outboards at the same time and allows you to quickly turn water off and on while you are at the motors.
  • Flush Twin Outboards at the Same Time
  • Attaches to any outboard flush port or ear muff flush devices
  • Connection Ends for Male or Female Connectors
  • Convenient Valve Turns Water On or Off and Adjusts Pressure, saves walk to spigot
  • Saves Time and Water

  • THDFMK-1-DP in action
     
    THMSS-1-DP   

    $34.95  1 pair

       
    Quantity in Basket: none
    MOTOR STIK Outboard Motor Support - Pair in Clam Package


    installed
    installation
    in use
    Packaged in pair for one engine
    MOTOR STIK™ Outboard Motor Support
    Pair (for one outboard motor)
    • Fits Over Trim Rams
    • Supports Your Outboard While Trailering
    • Takes the Pressure Off of Hydraulic System
    • Most Outboards 150hp and Up
    • Strong Aluminum Tubing with Molded Ends
    • Safe for Salt or Fresh Water

    NOTE - Some Yamaha motors have a grease fitting on the port side ram. Use a single Motor Stik™ on the starboard side only in this application

     
    THQF-1K-DP   

    $16.95 

       
    Quantity in Basket: none
    Quick Flush Outboard Engine Flush Kit Complete Kit Johnson Evinrude


    Quick Flush™ Outboard Flush Fitting Complete Kit for Johnson/Evinrude
    T-H Marine introduces a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating watter pressure keeps the valve sealed when using engine. Check out these features:
  • Makes flushing outboard quick and easy
  • Unique Patented slide valve replaces outboard flushing port plug
  • O-ring seal closes off port when operating engine
  • Quick connect on hose snaps onto valve for flushing
  • No plug to remove and no difficult turning of hose into port
  • Takes the hassle out of flushing your outboard
  • Fits all outboards equipped with a flushing port
  • Kit consists of Patented slide valve, hose quick connector, and washer
  •  
    THQF-2K-DP   

    $16.95 

       
    Quantity in Basket: none
    Quick Flush Outboard Engine Flush Kit Complete Kit Mercury Yamaha


    Quick Flush™ Outboard Flush Fitting Complete Kit for Mercury, Yamaha and other outboards
    T-H Marine introduces a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating watter pressure keeps the valve sealed when using engine. Check out these features:
  • Makes flushing outboard quick and easy
  • Unique Patented slide valve replaces outboard flushing port plug
  • O-ring seal closes off port when operating engine
  • Quick connect on hose snaps onto valve for flushing
  • No plug to remove and no difficult turning of hose into port
  • Takes the hassle out of flushing your outboard
  • Fits all outboards equipped with a flushing port
  • Kit consists of Patented slide valve, hose quick connector, and washer
  •  
    THQFV-2-DP   

    $12.95 

    Sorry, THQFV-2-DP is temporarily backordered. Please check back later.


    Quantity in Basket: none
    Quick Flush Outboard Engine Flush Kit Slide Valve Only Mercury Yamaha


    Quick Flush™ Outboard Flush Fitting Slide Valve (installs on Mercury, Yamaha and other outboard motors)
    T-H Marine introduces a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating watter pressure keeps the valve sealed when using engine. Check out these features:
  • Makes flushing outboard quick and easy
  • Unique Patented slide valve replaces outboard flushing port plug
  • O-ring seal closes off port when operating engine
  • Quick connect on hose snaps onto valve for flushing
  • No plug to remove and no difficult turning of hose into port
  • Takes the hassle out of flushing your outboard
  • Fits all outboards equipped with a flushing port
  • Kit consists of Patented slide valve, hose quick connector, and washer
  •  
    THSS-1-DP   

    $14.95 

       
    Quantity in Basket: none
    Steer-Stop - Steering Lock for Hydraulic Steering Systems 4 Inch


    installed
    4" Steer-Stop™ - Steering Lock for Hydraulic Steering Systems
    Locks Hydraulic Steering when Trailering

    T-H Marine developed the first steering stop available for outboards.  Outboards equipped with hydraulic steering from "wandering" when trailering. Units clip onto hydraulic steering rams on either side of outboard to keep engine straight and prevent damage to motor supports. Cord keeps units together when stowed and aids removal.

    • Locks hydraulic steering when trailering
    • Fits most steering cylinder rods on outboard engines
    • Snaps over outboards hydraulic steering cylinder rods
    • Helps keep engine centered during transport.
    • Protects steering system, outboard, and motor supports
    • Includes cord to connect units for storage and to aid in removal
    • Simple to take on and off 
    •  
    THWDSW-3-B   

    $68.95 

    Sorry, THWDSW-3-B is temporarily backordered. Please check back later.


    Quantity in Basket: none
    Boat Wash Down Station Marine Boat Lid 15 ft White Hose Pistol Grip Nozzle


    Boat Wash Down Station - White Hose - Pistol Grip Nozzle - Sand Shell Lid
    Flush Mounted Wash Down Station with Lid
  • Storage Tube with Screw Out Cover
  • Includes 15 Feet of High Quality Poly Coiled Hose
  • Includes Plumbing Fitting to Attach to Wash Down Pump
  • Wash Down Station Dimensions